4.7.2. Removal and installation of a gear belt, engines of 1.9 l (AVB, AWX, AVF)

The description belongs to the drive a gear belt with hydraulic damping of a tension roller. Its sign is existence of a damper (12). Instructions for the drive are provided by a gear belt with the tension roller having damping by friction in the end of the Head.

GRM Zubchatoremyonny drive. Diesel engines of 1.9 l (AVB, AWX, AVF)

1 — the Cover of a gear belt top. For removal remove an air duct to the forward panel. At installation accurately connect to the central cover of a gear belt
2 — the Gear belt
3 — the Nut, 20 Nanometers + 45 °
4 — the Tension roller
5 — the Bolt, 100 Nanometers
6 — the Bolt, 25 Nanometers
7 — a camshaft Wheel. Mark situation
8 — the Nave with a gear wheel for Hall's sensor
9 — the Bolt, 10 Nanometers. It is rolled on sealant
10 — the Cover of a gear belt, back
11 — the Rubber plug. In the presence of damages replace
12 — the Damper of a natyazhitel of a belt
13 — the Directing roller
14 — the Pump of cooling liquid

15 — the Wheel of a gear belt of a bent shaft. On an adjacent surface between a wheel of a gear belt and a bent shaft there should not be an oil. Installation is possible only in one situation
16 — the Bolt *, 120 Nanometers + 90 °. Not to grease
17 — the Bolt, 15 Nanometers
18 — the Bolt, 20 Nanometers
19 — the Cover of a gear belt lower
20 — the Wheel of a bent shaft (a damper of tortional fluctuations). Installation is possible only in one situation, openings are displaced
21 — the Bolt *, 10 Nanometers + 90 °
22 — the Cover
23 — the Cover of a gear belt central. For removal remove the top cover of a gear belt and disconnect the device of a tension of a maple belt
*) Surely replace.

Removal

 PERFORMANCE ORDER

  1. Install the forward panel in situation for service, address the Section Installation of the Forward Panel in situation for maintenance.
  1. Take out the index of level of oil (1) from the directing pipe.
  1. Disconnect covers and turn off the nuts (arrow) lying under them.
  2. Remove the top cover of the engine.
  3. Remove the damper lying under it.
  4. Again insert against the stop the index of level of oil.
  5. Take off maple a belt, address the Section Removal and installation of a belt of the drive of auxiliary units.
  1. Holding a fan pulley with the viscous coupling by means of the tool 3212, turn off it a face key on 8 mm (1) from the holder.
  1. Remove the fan with the viscous coupling and put it in a fan casing.
  2. Remove the generator and take out the fan with the viscous coupling from a casing, address the Section Removal and installation of the generator.
  1. Turn out screws (1) and (2) and remove the device of a tension of a maple belt.
  1. Remove the top cover of a gear belt.
  1. Turn out screws (3) and uncover (2).
  1. Take aside the electromagnetic valve of adjustment of pressure of pressurization (1).
  1. Uncover at a pulley of a bent shaft (a damper of tortional fluctuations) and turn off a pulley.

For an otvorachivaniye and fastening of a pulley hold it a cap key for the central bolt.

  1. Disconnect the central and lower covers of a gear belt (an arrow on an accompanying illustration).

The bent shaft is allowed to be turned only in the direction of rotation of the engine, i.e. clockwise. The bent shaft by a key for the central bolt is turned.

  1. Turn a bent shaft and establish it in the provision of VMT of the first cylinder. At the same time the interval between pads (1) on a rotor of the sensor of the camshaft has to lie against marking "4Z" (2) on a back cover of a gear belt.

    On an accompanying illustration for descriptive reasons the wheel is shown without gear belt.


  1. Record a nave HAZET 2588-3 finger.

Instead of the specified finger it is possible to apply a mandrel with a diameter of 6 mm.

  1. Record a pulley of a bent shaft HAZET 2588-1 finger. For this purpose insert the special tool (a stopper of a bent shaft) from an end face of a wheel of a gear belt into its gear wreath.

Tags on a cogwheel of a bent shaft (2) and the fixing tool (1) have to be opposite to each other. At the same time the pin of the tool has to enter an opening of a sealing flange. If such tool is unavailable, apply VMT tag on a sealing flange.

  1. Turn off bolts of fastening (arrow) so that a wheel of the camshaft it was turned in oblong openings.
  1. Insert a face key against the stop into a six-sided opening of a tension roller and turn a tension roller counterclockwise (the direction of an arrow on an accompanying illustration) so that the device of a tension could be fixed by a lock level of HAZET 2588-2.

The face key is inserted against the stop in order that it was not damaged at turn of a tension roller.

The tension element of a gear belt has oil damping and it is necessary to press it evenly, without application of considerable efforts.

  1. If the gear belt which was in work is established, note on it chalk or a felt-tip pen the direction of rotation.
  2. Turn off a nut of fastening of a tension roller.
  1. Turn out bolts (arrows on an accompanying illustration) the tension device of a gear belt and remove the tension device.
  1. Take off a gear belt.

Installation (adjustment of phases of gas distribution)

 PERFORMANCE ORDER

  1. Check whether are fixed the camshaft by HAZET 2588-3 finger, and a bent shaft HAZET 2588-1 stopper, and also whether the device of a tension of a gear belt is fixed by a lock plate of HAZET 2588-2.

Adjusting works with a gear belt are allowed to be performed only on the cold engine.

At a provorachivaniye of a bent shaft its stop at position of any piston in VMT is not allowed. At the same time there is a danger of damage of valves and/or the bottoms of pistons. If necessary, turn off a bent shaft back on a corner 90 °.

  1. Screw bolts by hand.

The wheel of the camshaft has to rotate and not overturn.

  1. Turn a camshaft wheel in its oblong openings against the stop.
  2. Put on a gear belt a camshaft wheel, a tension roller, a wheel of a bent shaft and in the last turn on a wheel of the pump of cooling liquid.
  3. Install the device of a tension of a gear belt.

Tension of a gear belt

 PERFORMANCE ORDER

  1. Turn the clown the HAZET 2587-1 tool counterclockwise against the stop (And) so that it was possible to take out a lock plate of HAZET 2588-2.
  1. Turn slowly the tension device clockwise (overcoming resistance) so that between the tension lever and the case it was possible to insert a drill (2) with a diameter of 4.0 mm easily. Size and = 4.0 ± 1.0 mm.
  1. Holding a tension roller in this situation tighten a nut of a tension roller (1) the moment of 20 Nanometers + 45 °.
  1. Tighten bolts (arrows on an illustration) fastenings of a wheel of the camshaft the moment of 25 Nanometers.
  1. Take out a lock finger of HAZET 2588-3 and a stopper of the bent shaft HAZET 2588-1.

The bent shaft is allowed to be rotated only in the direction of rotation of the engine.

  1. Turn a bent shaft 2 turns farther clockwise so that it stopped in the provision of VMT of the first cylinder again.
  1. Double-check the and size between the tension lever and the case of the tension device. The required value: and = 4.0 ± 1.0 mm.
  2. If the and size is not reached, tighten a tension roller in a way described below.
  3. Holding a tension roller the HAZET 2587-1 tool, turn off a nut (1). After that on action of effort of the tension device release it so (arrow) to reach the and size. The required value and = 4.0 ± 1.0 mm.
  4. Holding a tension roller in this situation, tighten a nut (1) the moment of 20 Nanometers + 45 °.

Check of phases of gas distribution

 PERFORMANCE ORDER

  1. For monitoring procedure record once again a wheel of a gear belt a stopper of the bent shaft HAZET 2588-1. At the same time keep in mind the following:
  • Tags on a wheel (2) and a stopper of a bent shaft (1) have to be opposite to each other. At the same time the pin of a stopper of a bent shaft (shooter) has to enter an opening of a sealing flange.
  • The pin of a stopper of a bent shaft at rotation has to enter an opening on a sealing flange (an arrow on an accompanying illustration).
  • If the bent shaft passed through a tag of VMT of the first cylinder, turn off a shaft on 90 ° back so that it again at rotation in the set direction stopped in the provision of VMT of the first cylinder.

Adjustment by rotation of a shaft back for the purpose of installation of a stopper is not allowed.

  1. Check whether the nave by means of a lock level of HAZET 2588-3 is fixed.
  1. The interval between pads (1) on a rotor of the sensor of the camshaft has to lie against marking "4Z" (2) on a back cover of a gear belt.

If the nave is not fixed

 PERFORMANCE ORDER

  1. Turn off bolts of fastening (arrow) of a wheel of the camshaft.
  1. Put a cap key on the central bolt of the camshaft and turn a nave so that the lock level of HAZET 2588-3 could enter.
  1. Tighten in this situation bolts of fastening (arrow) of a wheel of the camshaft the moment of 25 Nanometers.
  1. Take away a lock finger of HAZET 2588-3 and a stopper of the bent shaft HAZET 2588-1.

The bent shaft is allowed to be turned only in the direction of rotation of the engine, i.e. clockwise.

  1. Turn a bent shaft on 2 turnovers of the direction of rotation, i.e. clockwise so that the bent shaft rose in the provision of VMT of the first cylinder again.
  2. Repeat control of phases of gas distribution.
  3. Put the fan with the viscous coupling in a casing.
  4. Install into place the generator, at the same time for simplification of installation of the generator of the plug of lock bolts beat out a little back, address the Section Removal and installation of the generator.
  5. Fix the fan with the viscous coupling a new bolt the moment of 45 Nanometers.
  6. Establish maple a belt, address the Section Removal and installation of a belt of the drive of auxiliary units.
  7. Install into place the forward panel, address the Section Installation of the Forward Panel in situation for maintenance.