4.6. 6-and 8-cylinder petrol engines

Engines have three inlet and two final valves on the cylinder. Each number of cylinders of the engine has 2 camshafts. At the V6 engine camshafts of final valves are set in motion by a gear belt, camshafts of inlet valves are set in motion by a chain from camshafts of final valves. At the V8 engine four camshafts, also as well as auxiliary units, are set in motion by several chains. Driving chains are located from a flywheel (side of the check point).

Block of cylinders, crankshaft and flywheel of the V6 engine

1 — the Bent shaft
Check of an axial side play:
New: 0.07 - 0.23 mm
Wear limit: 0.25 mm
Check of a radial gap by means of Plastigage: 0.018 - 0.045 mm
Wear limit: 0.10 mm
Attention: When checking a radial gap do not rotate a bent shaft.
2 — the Cover of the radical bearing 4 with dredging for a persistent washer
3 — the Bolt. Replace, 60 Nanometers +90 °. For measurement of a radial gap tighten a bolt by effort no more than 60 Nanometers
4 — the Persistent washer of the radical bearing 4
5 — the Flywheel / the Driving disk

6 — a flywheel Bolt / a driving disk. Replace, (a flywheel of 60 Nanometers +180 °), (a driving disk 60 of Nanometer +90 °). At an otdavaniye use the tool 3242 for blocking of a bent shaft
7 — Inserts of radical bearings. Do not mix the removed inserts
8 — the Tight flange with an epiploon. It is replaced assembled. Before removal merge cooling liquid
9 — Laying. Replace
10 — the Bolt, 10 Nanometers
11 — the Persistent washer of the block of cylinders, the bearing 4
12 — the Bolt, 25 Nanometers. Previously tighten by hand before tightening bolts of a cover of the radical bearing
13 — the Block of cylinders
14 — the Directing plug

Basic elements of the GRM drive of the V6 engine

1 — the Bolt, 55 Nanometers
2 — Natyazhitel of a gear belt. Before removal block by means of the tool 3204
3 — the Top right cover of a gear belt
4 — the Central right cover of a gear belt
5 — the Gear belt. Before removal mark the direction of the movement of a belt. Check for wear. Do not bend
6 — the Top left cover of a gear belt
7, 8 — the Bolt, 25 Nanometers
9 — the Washer
10 — the bearing Plug
11 — the Tension roller of a gear belt
12 — the Tension lever
13 — the Sealing ring
14 — the Bolt, 25 Nanometers
15 — the Arm
16 — Connection (the thermostat case)
17 — the Water pump
18 — the Oil pump

19 — the Head of cylinders
20 — the Case of a sapun of a case
21 — the Block of cylinders
22 — the Bolt, 45 Nanometers
23 — the Arm
24 — the case Pallet
25 — the Directing roller
26 — the Bolt, 45 Nanometers
27 — a crankshaft Cogwheel
28 — the Bolt of 200 Nanometers +180 °, replace
29 — Natyazhitel of a belt
30 — the Bolt, 10 Nanometers. Establish with D6 lubricant
31 — a fan Pulley
32 — M8 Bolt - 25 Nanometers, M6 - 10 Nanometers
33 — the Cover of a gear belt
34 — the Bolt, 10 Nanometers
35 — the Damper of tortional fluctuations
36 — the Bolt, 25 Nanometers

Chain drive of a cam-shaft of inlet valves. V6 engine


1 — the Top right cover of a gear belt
2 — the Central right cover of a gear belt
3 — the Top left cover of a gear belt
4 — the Six-sided nut, 10 Nanometers
5 — the Back cover of a gear belt
6 — the Lifting eye
7 — the Bolt, 25 Nanometers
8 — Laying of a cover of a head of cylinders. At damage replace. Before installation grease the surface of laying between a cover of the bearing and a head of cylinders A3 lubricant D 454 300
9 — the Cover of a head of cylinders

10 — Laying
11 — the Cover. At damage replace laying
12 — the Arm
13 — the Six-sided nut, 10 Nanometers. Tighten in the direction from the center outside
14 — the Bolt of a head of cylinders. Replace
15 — the Head of cylinders. Check planeness
16 — Maslootrazhatel
17 — Laying of a head of cylinders (metal). Replace
18 — the Cogwheel of a bent shaft
19 — the Tightening plate
20 — the Bolt, 55 Nanometers

Elements of a head of cylinders. V6 engine

1 — the Double cover of bearings. Slightly grease the interfaced surface with AV 174 004 01 lubricant
2 — the Bolt, 10 Nanometers
3 — Covers of bearings of the camshaft of final valves. Slightly grease the interfaced surfaces of extreme (external) bearings with AV 174 004 01 lubricant
4 — the Camshaft of final valves. Check of a radial gap by means of Plastigage:
Beating, no more: 0.01 mm
Wear limit: 0.10 mm
5 — the Cap. Replace. For removal uncover the bearing. At the napressuyta established to a bearing cover by means of the tool 3202 and the plastic hammer
6 — Covers of bearings of the camshaft of inlet valves
7 — the Camshaft of final valves
8 — the camshaft Regulator. Before removal block 3366 natyazhitel of a chain by means of a clamp. Check adjustment of the camshaft
9 — the Driving chain. Before removal mark the direction of the movement
10 — the Bolt, 10 Nanometers
11 — the Sealing ring. Replace
12 — the Valve 1 or 2 for adjustment of the N205 or N208 camshaft. Check adjustment of the camshaft

13 — Laying (rubber/metal). Replace
14 — the Segment insert. Replace
15 — the Hydraulic pusher of the valve. Do not interchange the position of pushers of different valves. You store the surface of contact with a camshaft cam down
16 — Crackers of the cutting lock
17 — the Holder of a valvate spring
18 — the Valvate spring
19 — the Maslootrazhatelny cap
20 — a valve pusher Rod
21 — the Head of cylinders
22 — Valves
23 — the Epiploon. Slightly grease epiploon sponges
24 — the CMP Gate
25 — the Conic washer
26 — the Bolt, 25 Nanometers
27 — the Sensor of position of the camshaft (CMP)
28 — the Bolt, 10 Nanometers
29 — the Directing plug